3-D Champagne Cork Candy Mold

In stock
SKU CMA0020126
$2.99

This 3D Champagne Cork Chocolate Candy Mold has 10 cavities 

Makes five 3D chocolate corks or ten flat back pieces

Chocolate Cork with both halves together (full 3D piece) will measure 2 inches High x 1-1/4 inches Wide x 1 inch Deep

1 Pound of chocolate will make approximately 13 solid 3D Corks or 26 Hollow Chocolate Corks or 26 flat back chocolate pieces

This is a chocolate mold will not withstand heat and is not dishwasher safe.

 

 

How to make a solid 3D chocolate piece of chocolate with this mold-

Fill each cavity with melted chocolate or candy coatings

Tap mold lightly on work surface to bring air bubbles to surface

Place in refrigerator for 5-10 minutes or until chocolate pieces easily release from mold.

Let chocolate pieces come to room temperature.

Using melted chocolate, adhere each side together. To reduce finger prints on chocolate, you can leave one side of your chocolate piece in your candy mold to hold it for you, evenly coat the back with chocolate and sandwich the other side right on top. Place the mold in the refrigerator for 5 minutes until both sides are completely adhered together.

 

How to make a hollow piece of chocolate using this mold-

Cut mold in half so you have 5 cavities on each side. Trim the lip or frame off of the mold.

Fill one side of mold with your melted chocolate

Place your empty side of the mold on top of side that you just filled.

Secure both sides together with binder clips. Rotate the mold until chocolate has covered the inside of each cavity.

Place in refrigerator and rotate to opposite side every 1 minute for 5 minutes.

After rotating a total of 5 times (5 minutes) let the mold set for another 5 minutes to completely harden.

Remove binder clips and release your chocolate from the mold.

 






 

No Product Reviews Available

This 3D Champagne Cork Chocolate Candy Mold has 10 cavities 

Makes five 3D chocolate corks or ten flat back pieces

Chocolate Cork with both halves together (full 3D piece) will measure 2 inches High x 1-1/4 inches Wide x 1 inch Deep

1 Pound of chocolate will make approximately 13 solid 3D Corks or 26 Hollow Chocolate Corks or 26 flat back chocolate pieces

This is a chocolate mold will not withstand heat and is not dishwasher safe.

 

 

How to make a solid 3D chocolate piece of chocolate with this mold-

Fill each cavity with melted chocolate or candy coatings

Tap mold lightly on work surface to bring air bubbles to surface

Place in refrigerator for 5-10 minutes or until chocolate pieces easily release from mold.

Let chocolate pieces come to room temperature.

Using melted chocolate, adhere each side together. To reduce finger prints on chocolate, you can leave one side of your chocolate piece in your candy mold to hold it for you, evenly coat the back with chocolate and sandwich the other side right on top. Place the mold in the refrigerator for 5 minutes until both sides are completely adhered together.

 

How to make a hollow piece of chocolate using this mold-

Cut mold in half so you have 5 cavities on each side. Trim the lip or frame off of the mold.

Fill one side of mold with your melted chocolate

Place your empty side of the mold on top of side that you just filled.

Secure both sides together with binder clips. Rotate the mold until chocolate has covered the inside of each cavity.

Place in refrigerator and rotate to opposite side every 1 minute for 5 minutes.

After rotating a total of 5 times (5 minutes) let the mold set for another 5 minutes to completely harden.

Remove binder clips and release your chocolate from the mold.

 






 

More Information
Use/care Direction N/A
Maximum Store Credit value N/A
Minimum Store Credit value N/A
Store Credit value N/A
Credit Rate N/A
Type of Store Credit value N/A
Store Credit values N/A
Write Your Own Review
You're reviewing:3-D Champagne Cork Candy Mold
Your Rating